Physical and dosimetric characterisation of different Contrast-Enhanced digital mammographic systems: A multicentric study.

PURPOSE: Contrast-enhanced digital mammography (CEDM) is a relatively new imaging technique recombining low- and high-energy mammograms to emphasise iodine contrast. This work aims to perform a multicentric physical and dosimetric characterisation of four state-of-the-art CEDM systems. METHODS: We evaluated tube output, half-value-layer (HVL) for low- and high-energy and average glandular dose (AGD) in a wide range of equivalent breast thicknesses. CIRS phantom 022 was used to estimate the overall performance of a CEDM examination in the subtracted image in terms of the iodine difference signal (S). To calculate dosimetric impact of CEDM examination, we collected 4542 acquisitions on patients. RESULTS: Even if CEDM acquisition strategies differ, all the systems presented a linear behaviour between S and iodine concentration. The curve fit slopes expressed in PV/mg/cm2 were in the range [92-97] for Fujifilm, [31-32] for GE Healthcare, [35-36] for Hologic, and [114-130] for IMS. Dosimetric data from patients were matched with AGD values calculated using equivalent PMMA thicknesses. Fujifilm exhibited the lowest values, while GE Healthcare showed the highest. CONCLUSION: The subtracted image showed the ability of all the systems to give important information about the linearity of the signal with the iodine concentrations. All the patient-collected doses were under the AGD EUREF 2D Acceptable limit, except for patients with thicknesses ≤35 mm belonging to GE Healthcare and Hologic, which were slightly over. This work demonstrates the importance of testing each CEDM system to know how it performs regarding dose and the relationship between PV and iodine concentration.

Safety of Inhomogeneous Dose Distribution IMRT for High-Grade Glioma Reirradiation: A Prospective Phase I/II Trial (GLIORAD TRIAL).

Glioblastoma multiforme (GBM) is the most aggressive astrocytic primary brain tumor, and concurrent temozolomide (TMZ) and radiotherapy (RT) followed by maintenance of adjuvant TMZ is the current standard of care. Despite advances in imaging techniques and multi-modal treatment options, the median overall survival (OS) remains poor. As an alternative to surgery, re-irradiation (re-RT) can be a therapeutic option in recurrent GBM. Re-irradiation for brain tumors is increasingly used today, and several studies have demonstrated its feasibility. Besides differing techniques, the published data include a wide range of doses, emphasizing that no standard approach exists. The current study aimed to investigate the safety of moderate-high-voxel-based dose escalation in recurrent GBM. From 2016 to 2019, 12 patients met the inclusion criteria and were enrolled in this prospective single-center study. Retreatment consisted of re-irradiation with a total dose of 30 Gy (up to 50 Gy) over 5 days using the IMRT (arc VMAT) technique. A dose painting by numbers (DPBN)/dose escalation plan were performed, and a continuous relation between the voxel intensity of the functional image set and the risk of recurrence in that voxel were used to define target and dose distribution. Re-irradiation was well tolerated in all treated patients. No toxicities greater than G3 were recorded; only one patient had severe G3 acute toxicity, characterized by muscle weakness and fatigue. Median overall survival (OS2) and progression-free survival (PFS2) from the time of re-irradiation were 10.4 months and 5.7 months, respectively; 3-, 6-, and 12-month OS2 were 92%, 75%, and 42%, respectively; and 3-, 6-, and 12-month PFS2 were 83%, 42%, and 8%, respectively. Our work demonstrated a tolerable tolerance profile of this approach, and the future prospective phase II study will analyze the efficacy in terms of PFS and OS.

Variations in Head and Neck Treatment Plan Quality Assessment Among Radiation Oncologists and Medical Physicists in a Single Radiotherapy Department.

BACKGROUND: Agreement between planners and treating radiation oncologists (ROs) on plan quality criteria is essential for consistent planning. Differences between ROs and planning medical physicists (MPs) in perceived quality of head and neck cancer plans were assessed. MATERIALS AND METHODS: Five ROs and four MPs scored 65 plans for in total 15 patients. For each patient, the clinical (CLIN) plan and two or four alternative plans, generated with automated multi-criteria optimization (MCO), were included. There was always one MCO plan aiming at maximally adhering to clinical plan requirements, while the other MCO plans had a lower aimed quality. Scores were given as follows: 1-7 and 1-2, not acceptable; 3-5, acceptable if further planning would not resolve perceived weaknesses; and 6-7, straightway acceptable. One MP and one RO repeated plan scoring for intra-observer variation assessment. RESULTS: For the 36 unique observer pairs, the median percentage of plans for which the two observers agreed on a plan score (100% = 65 plans) was 27.7% [6.2, 40.0]. In the repeat scoring, agreements between first and second scoring were 52.3% and 40.0%, respectively. With a binary division between unacceptable (scores 1 and 2) and acceptable (3-7) plans, the median inter-observer agreement percentage was 78.5% [63.1, 86.2], while intra-observer agreements were 96.9% and 86.2%. There were no differences in observed agreements between RO-RO, MP-MP, and RO-MP pairs. Agreements for the highest-quality, automatically generated MCO plans were higher than for the CLIN plans. CONCLUSIONS: Inter-observer differences in plan quality scores were substantial and could result in inconsistencies in generated treatment plans. Agreements among ROs were not better than between ROs and MPs, despite large differences in training and clinical role. High-quality automatically generated plans showed the best score agreements.

A Multicentre Evaluation of Dosiomics Features Reproducibility, Stability and Sensitivity.

Dosiomics is a texture analysis method to produce dose features that encode the spatial 3D distribution of radiotherapy dose. Dosiomic studies, in a multicentre setting, require assessing the features' stability to dose calculation settings and the features' capability in distinguishing different dose distributions. Dose distributions were generated by eight Italian centres on a shared image dataset acquired on a dedicated phantom. Treatment planning protocols, in terms of planning target volume coverage and dose-volume constraints to the organs at risk, were shared among the centres to produce comparable dose distributions for measuring reproducibility/stability and sensitivity of dosiomic features. In addition, coefficient of variation (CV) was employed to evaluate the dosiomic features' variation. We extracted 38,160 features from 30 different dose distributions from six regions of interest, grouped by four features' families. A selected group of features (CV < 3 for the reproducibility/stability studies, CV > 1 for the sensitivity studies) were identified to support future multicentre studies, assuring both stable features when dose distributions variation is minimal and sensitive features when dose distribution variations need to be clearly identified. Dosiomic is a promising tool that could support multicentre studies, especially for predictive models, and encode the spatial and statistical characteristics of the 3D dose distribution.

Artificial intelligence applications in medical imaging: A review of the medical physics research in Italy.

PURPOSE: To perform a systematic review on the research on the application of artificial intelligence (AI) to imaging published in Italy and identify its fields of application, methods and results. MATERIALS AND METHODS: A Pubmed search was conducted using terms Artificial Intelligence, Machine Learning, Deep learning, imaging, and Italy as affiliation, excluding reviews and papers outside time interval 2015-2020. In a second phase, participants of the working group AI4MP on Artificial Intelligence of the Italian Association of Physics in Medicine (AIFM) searched for papers on AI in imaging. RESULTS: The Pubmed search produced 794 results. 168 studies were selected, of which 122 were from Pubmed search and 46 from the working group. The most used imaging modality was MRI (44%) followed by CT(12%) ad radiography/mammography (11%). The most common clinical indication were neurological diseases (29%) and diagnosis of cancer (25%). Classification was the most common task for AI (57%) followed by segmentation (16%). 65% of studies used machine learning and 35% used deep learning. We observed a rapid increase of research in Italy on artificial intelligence in the last 5 years, peaking at 155% from 2018 to 2019. CONCLUSIONS: We are witnessing an unprecedented interest in AI applied to imaging in Italy, in a diversity of fields and imaging techniques. Further initiatives are needed to build common frameworks and databases, collaborations among different types of institutions, and guidelines for research on AI.

On the dependence of quantitative diffusion-weighted imaging on scanner system characteristics and acquisition parameters: A large multicenter and multiparametric phantom study with unsupervised clustering analysis.

PURPOSE: The purpose of this multicenter phantom study was to exploit an innovative approach, based on an extensive acquisition protocol and unsupervised clustering analysis, in order to assess any potential bias in apparent diffusion coefficient (ADC) estimation due to different scanner characteristics. Moreover, we aimed at assessing, for the first time, any effect of acquisition plan/phase encoding direction on ADC estimation. METHODS: Water phantom acquisitions were carried out on 39 scanners. DWI acquisitions (b-value = 0-200-400-600-800-1000 s/mm2) with different acquisition plans (axial, coronal, sagittal) and phase encoding directions (anterior/posterior and right/left, for the axial acquisition plan), for 3 orthogonal diffusion weighting gradient directions, were performed. For each acquisition setup, ADC values were measured in-center and off-center (6 different positions), resulting in an entire dataset of 84 × 39 = 3276 ADC values. Spatial uniformity of ADC maps was assessed by means of the percentage difference between off-center and in-center ADC values (Δ). RESULTS: No significant dependence of in-center ADC values on acquisition plan/phase encoding direction was found. Ward unsupervised clustering analysis showed 3 distinct clusters of scanners and an association between Δ-values and manufacturer/model, whereas no association between Δ-values and maximum gradient strength, slew rate or static magnetic field strength was revealed. Several acquisition setups showed significant differences among groups, indicating the introduction of different biases in ADC estimation. CONCLUSIONS: Unsupervised clustering analysis of DWI data, obtained from several scanners using an extensive acquisition protocol, allows to reveal an association between measured ADC values and manufacturer/model of scanner, as well as to identify suboptimal DWI acquisition setups for accurate ADC estimation.

EPID-based 3D dosimetry for pre-treatment FFF VMAT stereotactic body radiotherapy plan verification using dosimetry CheckTM.

PURPOSE: The software Dosimetry Check (DC) reconstructs the 3D dose distribution on CT images data set by using EPID measured signal. This study aimed to evaluate DC for stereotactic body radiotherapy (SBRT) with unflattened photon beams (FFF) for dosimetric independent plan verification in pre-treatment modality. METHODS: DC v.4.1 was configured for Varian TrueBeam STx FFF beams equipped with EPID aS-1200. The DC FFF models were tested using arc open fields (from 1×1 cm2 to 15×15 cm2) and VMAT (Volumetric Modulated Arc Therapy) SBRT plans on phantom and patient CTs. DC dose distributions (DDC) were compared with that calculated by Eclipse with Acuros XB algorithm (DAXB) and one measured by Octavius 1000 SRS detector (DOCT). All differences were quantified in terms of the local 3D gamma passing rate (%GP), DVH and point dose differences. RESULTS: DC was configured for FFF VMAT using an appropriate correction procedure. %GP2%2mm (mean±standard deviation) of DOCT-DDC was 96.3±2.7% for open fields whereas it was 90.1±5.9% for plans on homogeneous phantom CT. However, average %GP3%3mm of DAXB-DDC was 95.0±4.1 for treatments on patient CT. The fraction of plans passing the %GP3%3mm DQA tolerance level [10% (50%) of maximum dose threshold] were 20/20 (14/20) and 18/20 (16/20) for OCT on phantom CT and DC on patient CT, respectively. CONCLUSIONS: DC characterization for FFF beams was performed. For stereotactic VMAT plan verifications DC showed good agreement with TPS whereas underlined discrepancies with Octavius in the high dose regions. A customized tolerance level is required for EPID-based VMAT FFF pre-treatment verification when DC system is applied.

Dependence of apparent diffusion coefficient measurement on diffusion gradient direction and spatial position - A quality assurance intercomparison study of forty-four scanners for quantitative diffusion-weighted imaging.

PURPOSE: To propose an MRI quality assurance procedure that can be used for routine controls and multi-centre comparison of different MR-scanners for quantitative diffusion-weighted imaging (DWI). MATERIALS AND METHODS: 44 MR-scanners with different field strengths (1 T, 1.5 T and 3 T) were included in the study. DWI acquisitions (b-value range 0-1000 s/mm2), with three different orthogonal diffusion gradient directions, were performed for each MR-scanner. All DWI acquisitions were performed by using a standard spherical plastic doped water phantom. Phantom solution ADC value and its dependence with temperature was measured using a DOSY sequence on a 600 MHz NMR spectrometer. Apparent diffusion coefficient (ADC) along each diffusion gradient direction and mean ADC were estimated, both at magnet isocentre and in six different position 50 mm away from isocentre, along positive and negative AP, RL and HF directions. RESULTS: A good agreement was found between the nominal and measured mean ADC at isocentre: more than 90% of mean ADC measurements were within 5% from the nominal value, and the highest deviation was 11.3%. Away from isocentre, the effect of the diffusion gradient direction on ADC estimation was larger than 5% in 47% of included scanners and a spatial non uniformity larger than 5% was reported in 13% of centres. CONCLUSION: ADC accuracy and spatial uniformity can vary appreciably depending on MR scanner model, sequence implementation (i.e. gradient diffusion direction) and hardware characteristics. The DWI quality assurance protocol proposed in this study can be employed in order to assess the accuracy and spatial uniformity of estimated ADC values, in single- as well as multi-centre studies.

A straightforward multiparametric quality control protocol for proton magnetic resonance spectroscopy: Validation and comparison of various 1.5 T and 3 T clinical scanner systems.

PURPOSE: The aim of this study was to propose and validate across various clinical scanner systems a straightforward multiparametric quality assurance procedure for proton magnetic resonance spectroscopy (MRS). METHODS: Eighteen clinical 1.5 T and 3 T scanner systems for MRS, from 16 centres and 3 different manufacturers, were enrolled in the study. A standard spherical water phantom was employed by all centres. The acquisition protocol included 3 sets of single (isotropic) voxel (size 20 mm) PRESS acquisitions with unsuppressed water signal and acquisition voxel position at isocenter as well as off-center, repeated 4/5 times within approximately 2 months. Water peak linewidth (LW) and area under the water peak (AP) were estimated. RESULTS: LW values [mean (standard deviation)] were 1.4 (1.0) Hz and 0.8 (0.3) Hz for 3 T and 1.5 T scanners, respectively. The mean (standard deviation) (across all scanners) coefficient of variation of LW and AP for different spatial positions of acquisition voxel were 43% (20%) and 11% (11%), respectively. The mean (standard deviation) phantom T2values were 1145 (50) ms and 1010 (95) ms for 1.5 T and 3 T scanners, respectively. The mean (standard deviation) (across all scanners) coefficients of variation for repeated measurements of LW, AP and T2 were 25% (20%), 10% (14%) and 5% (2%), respectively. CONCLUSIONS: We proposed a straightforward multiparametric and not time consuming quality control protocol for MRS, which can be included in routine and periodic quality assurance procedures. The protocol has been validated and proven to be feasible in a multicentre comparison study of a fairly large number of clinical 1.5 T and 3 T scanner systems.

Diagnostic performances of [18F]fluorocholine positron emission tomography in brain tumors.

BACKGROUND: Brain tumors characterization by molecular imaging that allows the depiction of brain lesions metabolic pattern is crucial. Our study aimed to: 1) to evaluate the diagnostic performances of [18F]fluoroethylcholine positron emission tomography/computed tomography ([18F]FECH PET/CT), and 2) correlate PET imaging derived parameters of [18F]FECH to survival in brain tumors. METHODS: From 2009 to 2012, we enrolled 30 patients who underwent [18F]FECH PET/CT. Final diagnosis was established by clinical and radiological follow-up. RESULTS: Final diagnosis was consistent with tumor disease in 27/30 cases. In 3/30 cases tumor disease was ruled out. [18F]FECH PET/CT resulted true positive and negative in 21/30 and 9/30 patients, respectively. Sensitivity, specificity, positive predictive value, negative predictive value and accuracy of [18F]FECH PET/CT were 78%, 100%, 100%, 33%, and 80%, respectively. Mean and maximum standardized uptake value (SUVmean and SUVmax) resulted statistically correlated to histology (P=0.0255 and P=0.0222, respectively). Using a SUVmax cut-off of 2.0 or 3.2, we distinguished between low- and high-grade gliomas with a good specificity (70% and 80%, respectively). SUVmax and histology resulted correlated to overall survival and disease related survival at multivariate analysis. CONCLUSIONS: Our results, worthy of further investigations, show high diagnostic performances of [18F]FECH PET/CT, and a correlation between PET imaging derived parameters and survival.

Contrast-enhanced spectral mammography in neoadjuvant chemotherapy monitoring: a comparison with breast magnetic resonance imaging.

BACKGROUND: Neoadjuvant-chemotherapy (NAC) is considered the standard treatment for locally advanced breast carcinomas. Accurate assessment of disease response is fundamental to increase the chances of successful breast-conserving surgery and to avoid local recurrence. The purpose of this study was to compare contrast-enhanced spectral mammography (CESM) and contrast-enhanced-MRI (MRI) in the evaluation of tumor response to NAC. METHODS: This prospective study was approved by the institutional review board and written informed consent was obtained. Fifty-four consenting women with breast cancer and indication of NAC were consecutively enrolled between October 2012 and December 2014. Patients underwent both CESM and MRI before, during and after NAC. MRI was performed first, followed by CESM within 3 days. Response to therapy was evaluated for each patient, comparing the size of the residual lesion measured on CESM and MRI performed after NAC to the pathological response on surgical specimens (gold standard), independently of and blinded to the results of the other test. The agreement between measurements was evaluated using Lin's coefficient. The agreement between measurements using CESM and MRI was tested at each step of the study, before, during and after NAC. And last of all, the variation in the largest dimension of the tumor on CESM and MRI was assessed according to the parameters set in RECIST 1.1 criteria, focusing on pathological complete response (pCR). RESULTS: A total of 46 patients (85%) completed the study. CESM predicted pCR better than MRI (Lin's coefficient 0.81 and 0.59, respectively). Both methods tend to underestimate the real extent of residual tumor (mean 4.1mm in CESM, 7.5mm in MRI). The agreement between measurements using CESM and MRI was 0.96, 0.94 and 0.76 before, during and after NAC respectively. The distinction between responders and non-responders with CESM and MRI was identical for 45/46 patients. In the assessment of CR, sensitivity and specificity were 100% and 84%, respectively, for CESM, and 87% and 60% for MRI. CONCLUSION: CESM and MRI lesion size measurements were highly correlated. CESM seems at least as reliable as MRI in assessing the response to NAC, and may be an alternative if MRI is contraindicated or its availability is limited.

Knowledge-based treatment planning: An inter-technique and inter-system feasibility study for prostate cancer.

PURPOSE: Helical Tomotherapy (HT) plans were used to create two RapidPlan knowledge-based (KB) models to generate plans with different techniques and to guide the optimization in a different treatment planning system for prostate plans. Feasibility and performance of these models were evaluated. MATERIAL AND METHODS: two sets of 35 low risk (LR) and 30 intermediate risk (IR) prostate cancer cases who underwent HT treatments were selected to train RapidPlan models. The KB predicted constraints were used to perform new 20KB plans using RapidArc technique (KB-RA) (inter-technique validation), and to optimise 20 new HT (KB-HT) plans in the Tomoplan (inter-system validation). For each validation modality, KB plans were benchmarked with the manual plans created by an expert planner (EP). RESULTS: RapidPlan was successfully configured using HT plans. The KB-RA plans fulfilled the clinical dose-volume requirements in 100% and 92% of cases for planning target volumes (PTVs) and organs at risk (OARs), respectively. For KB-HT plans these percentages were found to be a bit lower: 90% for PTVs and 86% for OARs. In comparison to EP plans, the KB-RA plans produced higher bladder doses for both LR and IR, and higher rectum doses for LR. KB-HT and EP plans produced similar results. CONCLUSION: RapidPlan can be trained to create models by using plans of a different treatment modality. These models were suitable for generating clinically acceptable plans for inter-technique and inter-system applications. The use of KB models based on plans of consolidated technique could be useful with a new treatment modality.

Quality assurance multicenter comparison of different MR scanners for quantitative diffusion-weighted imaging.

PURPOSE: To propose a magnetic resonance imaging (MRI) quality assurance procedure that can be used for multicenter comparison of different MR scanners for quantitative diffusion-weighted imaging (DWI). MATERIALS AND METHODS: Twenty-six centers (35 MR scanners with field strengths: 1T, 1.5T, and 3T) were enrolled in the study. Two different DWI acquisition series (b-value ranges 0-1000 and 0-3000 s/mm(2) , respectively) were performed for each MR scanner. All DWI acquisitions were performed by using a cylindrical doped water phantom. Mean apparent diffusion coefficient (ADC) values as well as ADC values along each of the three main orthogonal directions of the diffusion gradients (x, y, and z) were calculated. Short-term repeatability of ADC measurement was evaluated for 26 MR scanners. RESULTS: A good agreement was found between the nominal and measured mean ADC over all the centers. More than 80% of mean ADC measurements were within 5% from the nominal value, and the highest deviation and overall standard deviation were 9.3% and 3.5%, respectively. Short-term repeatability of ADC measurement was found <2.5% for all MR scanners. CONCLUSION: A specific and widely accepted protocol for quality controls in DWI is still lacking. The DWI quality assurance protocol proposed in this study can be applied in order to assess the reliability of DWI-derived indices before tackling single- as well as multicenter studies.

RIS-PACS, patient safety, and clinical risk management.

PURPOSE: Clinical risk management is the basis of safety procedures also in radiological workflows. In the literature, it has been documented that the incidence of reconciled radiological studies ranges between 0.2 and 0.5 % of stored studies, a non-negligible value if we consider the high number of diagnostic tests performed. MATERIALS AND METHODS: In radiology, "non-compliance" or, more generally, data to be reconciled means any circumstance in which wrong information is recorded in RIS and/or PACS, which requires processing to amend or correct images, reports or other information in order to attribute them to the right patient/episode. Non-compliance corrections account for almost 50 % of the medical system administrator's (SA) workload. This paper describes how the Reggio Emilia Province Diagnostic Imaging and Laboratory Medicine Department manages risk in clinical radiology, in compliance with Regional indications on RIS-PACS safety. A dedicated RIS webpage has been developed in order to manage reconciliation requests. Native integration with PACS makes information about ongoing reconciliations available to anyone who consults the images. RESULTS: In 2013, non-compliances reported by radiology staff ranged between 0.25 and 0.35 % of studies sent to the PACS. More than 50 % of non-compliances can be related to high clinical risk, which requires implementation of efficient and effective rapid mechanisms of action-reaction inside and outside the radiology department. CONCLUSIONS: The RIS-integrated module has been the starting point for managing and monitoring errors, allowing improvement initiatives to guarantee and optimise workflow. Request and event traceability have allowed us to define personalised training programmes, designed to minimise procedural and/or systematic errors. To protect the availability and consistency of information produced by radiology units, it is necessary to provide integrated and effective mechanisms for reconciliation management. The integrated tool described in this paper is now widely used (not only by our centre): radiographers and radiologists can indicate non-compliances in an efficient and effective manner, informing all the operators involved with just a click of the mouse. Similar functionality should be implemented in the next generation of RIS-PACS in order to maintain the highest possible safety level for patients and workers.

Radiation protection procedures in 131I treatments for thyroid cancer in patients requiring hemodialysis.

BACKGROUND: Hemodialysis is essential for patients with renal failure, and iodine-131 ((131)I) administration is the standard of care in thyroid carcinoma treatment. Although the need for hemodialysis during (131)I treatment is very rare, it raises some concerns due to the involvement of personnel not exposed to radiation and to the contamination of devices used for other patients. In this paper, a radioprotection protocol to perform hemodialysis safely on patients during (131)I treatment has been presented. PATIENTS AND METHODS: The exposure of personnel who assisted 13 patients over the course of 10 years was monitored: external exposure was measured through electronic dosimeters, and internal contamination was checked by thyroid uptake and urine sample gamma spectrometry. Over this period, room layout was optimized to allow an improvement of radioprotection procedures.Two nurses were involved in patient assistance. RESULTS: After hemodialysis, measurements of internal contamination were below the minimum detectable activity and external exposure was in the range of 1-82 µSv in terms of H(p)(10). A reduction in personnel exposure was observed after hospitalization room renovation: H(p)(10) normalized to the activity administered to the patient was about halved. CONCLUSION: The data show that hemodialysis can be performed safely during I treatments when appropriate radioprotection actions are implemented.

MR scanner systems should be adequately characterized in diffusion-MRI of the breast.

Breast imaging represents a relatively recent and promising field of application of quantitative diffusion-MRI techniques. In view of the importance of guaranteeing and assessing its reliability in clinical as well as research settings, the aim of this study was to specifically characterize how the main MR scanner system-related factors affect quantitative measurements in diffusion-MRI of the breast. In particular, phantom acquisitions were performed on three 1.5 T MR scanner systems by different manufacturers, all equipped with a dedicated multi-channel breast coil as well as acquisition sequences for diffusion-MRI of the breast. We assessed the accuracy, inter-scan and inter-scanner reproducibility of the mean apparent diffusion coefficient measured along the main orthogonal directions () as well as of diffusion-tensor imaging (DTI)-derived mean diffusivity (MD) measurements. Additionally, we estimated spatial non-uniformity of (NU) and MD (NUMD) maps. We showed that the signal-to-noise ratio as well as overall calibration of high strength diffusion gradients system in typical acquisition sequences for diffusion-MRI of the breast varied across MR scanner systems, introducing systematic bias in the measurements of diffusion indices. While and MD values were not appreciably different from each other, they substantially varied across MR scanner systems. The mean of the accuracies of measured and MD was in the range [-2.3%,11.9%], and the mean of the coefficients of variation for and MD measurements across MR scanner systems was 6.8%. The coefficient of variation for repeated measurements of both and MD was < 1%, while NU and NUMD values were <4%. Our results highlight that MR scanner system-related factors can substantially affect quantitative diffusion-MRI of the breast. Therefore, a specific quality control program for assessing and monitoring the performance of MR scanner systems for diffusion-MRI of the breast is highly recommended at every site, especially in multicenter and longitudinal studies.

Personnel exposure in labelling and administration of (177)Lu-DOTA-D-Phe1-Tyr3-octreotide.

OBJECTIVE: The introduction of peptide receptor radionuclide therapy, mainly performed with (90)Y and (177)Lu-labelled somatostatin analogues, has widened the therapeutic horizon of nuclear medicine.The handling of (177)Lu-labelled pharmaceuticals implies an increase of the personnel exposure and this aspect is evaluated in this paper, in comparison with personal exposure in (90)Y manipulation. MATERIALS AND METHODS: Personal dose measurements were performed during 26 (177)Lu-DOTATOC preparations by using a series of thin active layer LiF: Mg,Cu,P thermoluminescence dosimeters fixed at the operator's fingertips to evaluate the skin equivalent dose and by means of direct reading dosimeters positioned at the chest to evaluate the personal effective dose. Individual protection devices, such as shielded aprons and anti-X gloves, were also used. RESULTS: The 95th percentile of the skin equivalent dose distribution for (177)Lu operations by using 0.20-mm anti-X gloves was 0.080 mSv/GBq for the chemist and 0.011 mSv/GBq for the physician, whereas the 75th percentile was 0.058 mSv/GBq for the chemist and 0.006 mSv/GBq for the physician. The use of the 0.25 mm Pb-equivalent anti-X apron halved the personal equivalent dose measured over the apron by a direct reading dosimeter. Skin doses were compared with (90)Y-DOTATOC procedures: no relevant exposure reduction is observed for chemists, whereas doses are considerably lower during administration procedures performed by physicians. CONCLUSION: In this study, an evaluation of the skin equivalent doses during (177)Lu-DOTATOC labelling and administration is presented. These data can be useful to assess the risk for workers in centres that are starting to implement PRRT using (177)Lu. The use of appropriate protection devices and procedures allows the observance of International Commission for Radiological Protection dose limits for exposed workers.

Comparison of two different types of LiF:Mg,Cu,P thermoluminescent dosimeters for detection of beta rays (beta-TLDs) from 90Sr/90Y, 85Kr and 147Pm sources.

Targeted radionuclide therapies in nuclear medicine departments increasingly depend on using unsealed beta radiation sources in the labeling of peptides and antibodies. Monitoring doses received by the fingers and hands during these procedures is best accomplished with TLD dosimeters that can be located at the fingertips. The present study examines the response of two TLD dosimeters (MCP-Ns and GR200A) to 90Sr/90Y, 85Kr, and 147Pm. The dosimeters were supplied by two different services, and all irradiations were performed at the PTB Institute in Germany. Each dosimetry service evaluated the dosimeters without knowledge that they had been purposefully irradiated. The accuracy and precision of the dosimeters were evaluated as a function of delivered dose, energy of beta particles and angular incidence. The results are compared to performance measures recommended by the IEC. Both dosimeter types displayed significant energy dependence. Angular dependence was moderate. Accuracy and precision as a function of dose (linearity) differed between the two systems, with the MCP-Ns being noticeably better than the GR200A. The superior precision makes the MCP-Ns much more useful for extremity dose measurements. The differences between these two dosimeter systems reinforce the need to evaluate a dosimeter carefully before using it in the daily work routine.

Contrast detail phantom comparison on a commercially available unit. Digital breast tomosynthesis (DBT) versus full-field digital mammography (FFDM).

The performance of a commercial digital mammographic system working in 2D planar versus tomosynthesis mode was evaluated in terms of the image signal difference to noise ratio (SDNR). A contrast detail phantom was obtained embedding 1 cm Plexiglas, including 49 holes of different diameter and depth, between two layers containing a breast-simulating material. The phantom was exposed with the details plane perpendicular to the X-ray beam using the manufacturer's standard clinical breast acquisition parameters. SDNR in the digital breast tomosynthesis (DBT) images was higher than that of the full-field digital mammography (FFDM) for 38 out of 49 details in complex background conditions. These differences (p < 0.05) are statistically significant for 19 details out of 38. The relative SDNR results for DBT and FFDM images showed a dependence on the diameter of the details considered. This paper proposes an initial framework for a global image quality evaluation for commercial systems that can operate with different image acquisition modality using the same detector.